Take advantage of the high performance and low noise level of the professional Dalap AP PROFI 150 inline duct fan. The fan is designed for air extraction from small and medium-sized rooms, such as bathrooms, showers, kitchens, greenhouses, cinemas, weekend houses, shops and more. It is designed for easy removal for maintenance, for which you need almost no tools. Max. length of the ventilation ducts is 8 to 10 metres.
Advantages of the Dalap AP Profi 150 inline duct fan
-
high air flow of 565 m3/h even at a very low noise level
- motor with ball bearing – service life of up to 40,000 hours
- smooth operation and reliability
- almost tool-free maintenance, even without dismantling the ventilation system
- compatible with all round ducts with a diameter of 150 mm
- installation in rigid as well as flexible ventilation ducts
Designed for easy removal
Thanks to the fan's easy disassembly, you can first complete the ventilation system and only then insert the fan's turbine. It's simple and requires almost no tools! First remove the retaining screws of the fasteners and open the tensioning straps. Then remove the turbine unit from the device.
Motor with ball bearing
The single-phase motor with ball bearing has two power levels, which you can select using a switch. The motor is equipped with overheating protection with automatic reset. Protection class is IPX4.
Installation anywhere in the ventilation system
The fan can be installed at any point in the duct system – vertically or horizontally. At the same time, several inline duct fans can also be installed in series to increase pressure build-up and thus the volume of air transported.
For duct systems of 8 to 10 metres
Thanks to its high pressure output, the Dalap AP PROFI inline duct fan is suitable for moving air in a duct with a maximum length of 8 to 10 metres.
Sufficient power for extraction through filters
The inline duct fan is designed to move air that is clean and free of mechanical dirt or grease, as the impeller or the fan itself could otherwise be damaged. If the fan needs to be used, for example, in the kitchen or in other locations with greasy air, it makes sense to install a grease filter in front of the device. The same applies in workshops, warehouses, garages or anywhere else where the air contains contaminants of various kinds. Here, a filter appropriate to the filter class should be installed in front of the fan.
Accessories
A necessary part for connecting the fan is a connecting cable, which is purchased separately.
External modules that can enhance the fan with a timer or a humidity sensor.
Connection
Difficulty level: requires expertise in electrical engineering
Tools required: small flat-head screwdriver
Time: 15 minutes
1. Remove the cover of the terminal box; here you will find 2 terminals
2. Each terminal is marked with a letter: from the left, the "N" terminal – for connecting the neutral conductor (blue cable)
3. Next you will find the "L" terminal – for connecting the phase conductor.
The fan's two power levels are controlled via the built-in switch.
Please also see our detailed guide on connecting an inline duct fan!
Technical data
| Diameter [mm] |
150 |
| Air flow [m³/h] |
415 / 565 |
| Static pressure [Pa] |
190 / 270 |
| Power consumption [W] |
42 / 50 |
| Speed [min] |
1940 / 2620 |
| Rated current [A] |
0,19 / 0,22 |
| Sound pressure [dB/3m] |
32 / 44 |
| Protection class [IP] |
X4 |
| Voltage [V] |
230 |
| Frequency [Hz] |
50 |
| Max. temperature [°C] |
60 |
| Weight [kg] |
2.3 |
| Dimensions [mm] |
see image |
| Application area |
office , bathroom , garage, workshop , living rooms |
| Ball bearing |
yes |
| Max. noise level [dB] |
44 |
| Operating temperature [°C] |
-25 to +60 |
| Colour |
grey |
| Control |
manual |
| Marking [CE] |
CE |
| Application |
for air extraction |
| Mounting |
into the ventilation duct |
| Version |
with speed switch |
| Service life |
40,000 hours |
| Fan design |
Axial |
| Model |
AP PROFI 150 |
